Focus-foodservice CAGES SECURITY with Aluminum Truck Dolly - Assembl Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Meubles Focus-foodservice CAGES SECURITY with Aluminum Truck Dolly - Assembl. Focus Foodservice CAGES SECURITY with Aluminum Truck Dolly - Assembly Instructions User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 4
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
ASSEMBLY INSTRUCTIONS
Security Cage with Aluminum Truck Dolly
FOODSERVICE, LLC
Part Truck Dolly Front Left Front Right w/Latch Sides Back
Steel
Insert Bolt
Assembly
Hardware
Qty 1 1 1 2 2 4 4
3
1
CAUTION: INSPECT CONTENTS IMMEDIATELY TO ENSURE PRODUCT WAS NOT DAMAGED DURING SHIPPING.
Step 1 Unpack carton, identify and confirm quality of components.
Step 2 Before assembly of shelving unit to Truck Dolly, unscrew the leveling feet on the posts (See Diagram 1).
Step 3 Attach the posts to Truck Dolly frame, using leveling feet and washers and tighten down (See Diagram 2).
Step 4 Assemble shelving unit with at least three shelves. The top shelf should be mounted at the top groove of the post.
The bottom shelf on a 74" post, in order to be inside the security enclosure, must be 13" above the dolly. If using
a 63" post and the bottom shelf should be located on the second groove from the bottom. Third shelf should be
placed in the middle of the posts.
Step 5 Remove the plastic top caps from all four posts (See Diagram 3).
Step 6 Install the steel inserts into the holes where the plastic top caps were (See Diagram 4). Make sure steel insert is
set all the way into the top of post. You may use a rubber mallet to secure the inserts.
DO NOT SCREW IN THE BOLTS UNTIL ALL PANELS ARE INSTALLED.
Step 7 Assemble the side panels with the loops on the bottom facing inward. Tilt the panel so the loops lock around the
posts on both ends and then slide down so the loops are on the posts (See Diagram 5). Align holes in guide plates
with steel insert at the top of the posts. Partially screw in bolt through guide plate into top of the front post. This
will keep side panel in place during the assembly process. Repeat with other panel.
Step 8 Assemble left side back panel first. Place the wires that are facing downward into the loops on each side panel
(See Diagram 6).
Step 9 Repeat the same for the right side back panel as in Step 8.
Step 10 Secure back panels with back panel assembly hardware. Install as shown (See Diagram 7). For greater security,
assemble uppermost plates through top shelf. Place additional securing clip at the bottom of the back panels.
(Push down so that the 2 prongs of the clip wrap over the truss of the bottom shelf.)
Step 11 Install the left front door assembly, by placing the side wires into the loops of the side panels.
Step 12 Repeat with right front door assembly as in Step 11.
Step 13 Line up holes of the guide plates in the top of the panels over the steel inserts in the top of the posts and screw
in bolts into posts (See Diagram 8). Tighten down bolts in front posts.
Vue de la page 0
1 2 3 4

Résumé du contenu

Page 1 - ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONSSecurity Cage with Aluminum Truck DollyFOODSERVICE, LLCPart Truck Dolly Front Left Front Right w/Latch Sides BackSteel Insert Bol

Page 2

ASSEMBLY INSTRUCTIONSCall Customer Service at 1.800.968.3918 | Fax 1.800.968.4129 www.focusfoodservice.comrev. 0811Note: Be sure that top & bo

Page 3 - INSTRUCCIONES DE ARMADO

INSTRUCCIONES DE ARMADOJaula de Seguridad con Carro de AluminioFOODSERVICE, LLCPieza Truck Dolly Front Left Front Right w/Latch Sides BackSteel Insert

Page 4 - INSTRUCCIONES DE ENSAMBLAJE

INSTRUCCIONES DE ENSAMBLAJECall Customer Service at 1.800.968.3918 | Fax 1.800.968.4129 www.focusfoodservice.comrev. 0911Note: Be sure that top &a

Commentaires sur ces manuels

Pas de commentaire