Focus-foodservice HDS-Plus High Density Storage System - Assembly In Manuel d'utilisateur télécharger pdf (Page 3)

SHELVING

Step 1 Connect track tube lengths using track joiners. To connect tubes with track joiners,

insert cap end of track joiner into tube section until it stops. Use wrench to tighten nut

on exposed end of track joiner until track joiner is snug in tubing. Take another section

of tube and twist onto exposed section of track joiner until two sections of tube meet.

Repeat process until both sections of track are assembled.

Step 2 Place locking collar on one end of fully assembled track length and tighten with Allen

wrench. Slide on ½ of the guide blocks, if your system requires a stationary

middle unit, place 1 locking collar on the track, then slide on 2 guide blocks then slide

on another locking collar. Do not tighten inner locking collars at this point. Then place

another locking collar on open end of tube and tighten with Allen wrench. Repeat

process with second section of track.

PART 4: OVERHEAD TRACK ASSEMBLY

Step 1 Line up Shelving Units in a straight line in the area where the unit will be installed. Allow a minimum of 30" of open aisle

space for each system. Bumpers add a minimum of 3" to the width of the mobile units. Place stationary units on the outside

and middle (as needed**) and mobile units on the inside. To ensure smooth movement of mobile sections take great care

that all shelving units are aligned in a straight line.

Note: Track lengths over 20 ft in length require a stationary unit in the middle of the system.

PART 5: INSTALL TRACK ASSEMBLY ONTO SHELVING UNITS

Step 2 Using two or more people, raise one section of track assembly over tops of posts and starting on one end of shelving

run. Insert guide blocks into tops of posts. Continue to opposite end. Repeat process with second section of track. Recheck

shelving sections to ensure they are in straight alignment. To adjust for uneven ﬂoor surfaces, turn triangle security feet on

stationary posts (clockwise or counter-clockwise). For systems with stationary units in the middle of the track, tighten down

the locking collars surrounding these units..

Step 1 Lay completed shelving unit(s) with 74" posts on their side.

Step 2 With the opening of the bumper facing towards the bottom, slide bumper

over bottom of posts.

Step 3 Install 6" Casters (FTSC6 - CASTER MUST POINT INWARD AS SHOWN) through

openings in caster channels (FTSU18, FTSU21 or FTSU24).

Step 4 Install caster/caster channel assembly into 74" posts (FGN074C or FGN074G) until

caster ﬁt is tight. If needed, use a rubber mallet and tap bottom of caster to drive

casters into posts. Repeat process for all mobile shelving units.

PART 3: CASTER ASSEMBLY OR MOBILE POST ASSEMBLY. Use 74" mobile posts.

1 2 3 4

Commentaires sur ces manuels

Pas de commentaire

Electrolux ESI6560ROW Manual de usuario (20 paginas)

Marca: Electrolux | Categoria: Washing machines | Tamaño: 2.43 MB |

Tabla de contenidos

ESI 6560RO

SOMMAIRE

NOUS PENSONS À VOUS

SERVICE APRÈS-VENTE

CONSIGNES DE SÉCURITÉ

1.3 Utilisation

1.4 Mise au rebut

3. BANDEAU DE COMMANDE

4. PROGRAMMES

5. OPTIONS

5.1 EnergySaver

5.2 Multitab

5.3 MyFavourite

5.4 Signaux sonores

FRANÇAIS 9

Réglage manuel

Réglage électronique

FRANÇAIS 11

8. CONSEILS

9. ENTRETIEN ET NETTOYAGE

9.2 Nettoyage des bras

9.3 Nettoyage extérieur

10.2 Comment activer le

L'ENVIRONNEMENT

FRANÇAIS 19

117919920-A-202012